Latest topics
» Cylinder head.
frame - Powerbike frame alignment EmptyYesterday at 5:59 pm by Rex Stewart

» Villiers 9E / 30 series lighting plug
frame - Powerbike frame alignment EmptyYesterday at 9:09 am by John Wakefield

» Whitch side is the left hand thread
frame - Powerbike frame alignment EmptyYesterday at 8:16 am by Kevin B Smith

» 6E clutch plate etc
frame - Powerbike frame alignment EmptyYesterday at 5:58 am by blackjak

» Help required with Falcon Trials project (scratch build)
frame - Powerbike frame alignment EmptyThu Jul 18, 2019 7:52 pm by Nigel Moth

» Fulmar seat
frame - Powerbike frame alignment EmptyThu Jul 18, 2019 6:55 pm by piston 197

» Fulmar Coil Problem
frame - Powerbike frame alignment EmptyThu Jul 18, 2019 5:15 pm by Rex Stewart

» New Member
frame - Powerbike frame alignment EmptyThu Jul 18, 2019 10:45 am by stevenbell

» Francis Barnett Green
frame - Powerbike frame alignment EmptyWed Jul 17, 2019 8:14 pm by Nigel Moth


Powerbike frame alignment

Go down

frame - Powerbike frame alignment Empty Powerbike frame alignment

Post  ztis1 on Sat Feb 10, 2018 7:15 pm

I've just started the restoration of a 1940 Powerbike 50 and I have a couple of questions regarding the frame.
Can anyone tell me what the rear hub width should be? My rear stays are bent outwards on the right hand side.
The seat tube also seems to be bent but, on close inspection it appears to be several sections brazed together out of alignment. Is this usual? I don't want to spend ages trying to sort it out 'if they're all like that' and it's not really an issue.

Any help greatly appreciated.
Regards, Ian.

ztis1

Posts : 6
Join date : 2018-02-09

Back to top Go down

frame - Powerbike frame alignment Empty Frame

Post  kerabo on Sat Feb 10, 2018 7:25 pm

If you dont get an answer I could measure my 56 if they are the same.

Have you not got the rear hub to aligh the stays. The wheel centre is going to be in line with the frame tube

Ken
kerabo
kerabo

Posts : 2679
Join date : 2008-02-11
Age : 69
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

frame - Powerbike frame alignment Empty Powerbike frame alignment

Post  ztis1 on Sun Feb 11, 2018 9:50 am

Thanks Ken,
I have the hub but suspect it may be incomplete. I can see from the flats on the spindle roughly where it needs to be.

ztis1

Posts : 6
Join date : 2018-02-09

Back to top Go down

frame - Powerbike frame alignment Empty Powerbike 50

Post  FB vincent on Sun Feb 11, 2018 10:41 am

I think you will find the width across the British Hub Co/Harwil rear brake assembly is 5 3/4", but as you say, the flats in the axle must align with the frame cut outs.

The Powerbike 50 frame is completely different to the 56 frame, which is of all welded construction intended for the later Villiers 2F engine.

If you need a copy of the Powerbike 50 instruction and parts book send me a PM with your email address, and I will forward you a copy.

Sandy

FB vincent

Posts : 688
Join date : 2009-01-20
Location : Hertfordshire

Back to top Go down

frame - Powerbike frame alignment Empty Powerbike 50

Post  ztis1 on Mon Feb 12, 2018 7:25 pm

Sandy,

Many thanks for the information regarding the hub.
I will PM you about the instuction manual (I have to wait 7 days as a new user)

Regards,
Ian

ztis1

Posts : 6
Join date : 2018-02-09

Back to top Go down

frame - Powerbike frame alignment Empty Re: Powerbike frame alignment

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum